aggregate impact value test report

  • AIV Lab Report - AGGREGATE IMPACT VALUE

    The aggregate impact value indicates a relative measure of the resistance of aggregate to a sudden shock or an impact, which in some aggregates differs from its resistance to a slow compressive load. The method of test covers the procedure for determining the aggregate impact value of coarse aggregates

  • (DOC) AGGREGATE IMPACT VALUE TEST | hong g.woei -

    The strength of coarse aggregates is assessed by aggregates impact test. The aggregate impact value provides a relative measure of resistance to crushing under a gradually applied compressive load. To achieve a high quality of pavement, lower aggregate impact value should be preferred. Toughness is the property of a material to resist impact.

  • Aggregate Impact Value Report | PDF | Construction ...

    2018-11-19 · Aggregate Impact Value (AIV) ASTM-D58-74. Introduction: Impact value of an aggregate is the percentage loss of weight particles passing 2.36mm sieve by the application of load by means of 15 blows of standard hammer and drop, under specified test condition. The aggregate impact value gives a relative measure of the resistance of an aggregate to sudden

  • Lab Report.docx - Determination of Aggregate Impact

    Crush samples having an impact value of 12.5% fall in the category of 10-20%, therefore, the aggregate test sample is classified as strong and can be seen in the table below. The aggregate impact value is useful for selecting the good aggregates for road construction. Aggregate appropriate for cement wearing course should have maximum AIV of 30%.

  • Aggregate Impact Value Test | Impact Test Of Aggregate ...

    2 天前 · Importance of Impact Test on Aggregates. The impact test on aggregate is carried out to know the response of aggregates to different kinds of loads that the aggregates will be subjected to during their service life.. The need for impact

  • Aggregate Impact Value Test Procedure as per IS 2386

    2020-3-30 · Read definition, apparatus, IS code, procedure, observations, formula, result and lab report about aggregate impact value test. Apparatus Required for Aggregate Impact Value Test:-Impact testing machine; Cylinder; A straight metal tamping rod of circular cross-section 16 mm in diameter, 45 cm to 60 cm in length and rounded at one end.

  • Aggregate Impact Value Testing | AIV TEST - Civil ...

    2018-1-9 · Aggregate Impact Value Test. AIV test is conducted to determine the Aggregate Impact Value of Coarse aggregate. The aggregate impact value gives a relative measure of the resistance of an aggregate to sudden shock or impact, which in some aggregates differs from Its resistance to a slow compression load.

  • IMPACT VALUE OF AGGREGATE - iricen.gov

    2019-3-11 · fresh test made. Two tests shall be made. 5.Calculation 1.The ratio of the weight of fines formed to the total sample weight in each test shall he expressed as a percentage, the result being recorded to the first decimal place: Aggregate Impact Value = (B/A) X 100 where A = weight in g of saturated surface - dry sample,

  • Aggregate Impact value Test Apparatus, Procedure and

    2019-7-1 · The apparatus of the aggregate impact value test consists of: A testing machine weighing 45 to 60 kg and having a metal base with a plane lower

  • Determination of Aggregate Impact Value - Impact Test on ...

    2010-2-22 · The aggregate impact value is a measure of resistance to sudden impact or shock, which may differ from its resistance to gradually applied compressive load. Procedure o f Aggregate Impact Test The test sample consists of aggregates sized 10.0 mm 12.5 mm. Aggregates may be dried by heating at 100-110° C for a period of 4 hours and cooled.

  • Lab Report.docx - Determination of Aggregate Impact

    Crush samples having an impact value of 12.5% fall in the category of 10-20%, therefore, the aggregate test sample is classified as strong and can be seen in the table below. The aggregate impact value is useful for selecting the good aggregates for road construction. Aggregate appropriate for cement wearing course should have maximum AIV of 30%.

  • Aggregate Impact Value Report | PDF | Construction ...

    2018-11-19 · Aggregate Impact Value (AIV) ASTM-D58-74. Introduction: Impact value of an aggregate is the percentage loss of weight particles passing 2.36mm sieve by the application of load by means of 15 blows of standard hammer and drop, under specified test condition. The aggregate impact value gives a relative measure of the resistance of an aggregate to sudden

  • Aggregate Impact Value Test | Construction Aggregate ...

    2017-10-4 · The test sample consist of aggregates passing 12.5 has been standardized by the So they must be tested for their mm sieve and retained on 10 mm sieve and dried in an Weight of aggregate(M1), g 313.4 315.4 329.1 British Standard The aggregate impact toughness before they are used in the oven for four hours at a temperature 100C to 110C and value ...

  • Aggregate impact value test- step by Step Procedure with ...

    Recommended aggregate impact value Precaution for aggregate impact value test. The sample of aggregate should be sieved in circular motion or movement. The sample aggregate should not be overheated on the oven. The weight of samples and dust should be tamped with the help of a standard size tamping rod.

  • Methods for determination of aggregate impact value

    2019-10-18 · Aggregate Impact Value (AIV) = 𝑾 𝑾 × Calculate the mean of the two results to the nearest whole number. Report the mean as the aggregate impact value, unless the individual results differ by more than 0.15 times the mean value. In

  • IMPACT VALUE OF AGGREGATE - iricen.gov

    2019-3-11 · fresh test made. Two tests shall be made. 5.Calculation 1.The ratio of the weight of fines formed to the total sample weight in each test shall he expressed as a percentage, the result being recorded to the first decimal place: Aggregate Impact Value = (B/A) X 100 where A = weight in g of saturated surface - dry sample,

  • Exp 4 Aggregate Impact Value - Civil Engineers PK

    Aggregate Impact Value; Test Specifications: Aggregate Impact Value. The test sample shall consist of aggregates the whole of which passes through ½ in B.S. test sieve and is retained on a 3/8 in B.S. test sieve. The aggregate comprising the test sample shall be dried in an oven for a period of four hours at a temperature of 100-110 °C and ...

  • Impact Test of Aggregate | Lab Test Procedure ...

    2 天前 · The procedure of the impact value test includes the following series of steps: 1. The aggregate samples of size 10mm to 12.5mm (passing through 12.5mm sieve and retained on 10mm sieve) are first taken and oven-dried at a temperature ranging from 100 degrees Celsius to 110 degrees Celsius for about four hours. 2.

  • Aggregate Impact value Test Apparatus, Procedure and

    2019-7-1 · The apparatus of the aggregate impact value test consists of: A testing machine weighing 45 to 60 kg and having a metal base with a plane lower surface of not less than 30 cm in diameter. Level and plane concrete floor of minimum 45 cm thickness are used to support it. The base of the machine should also have provisions for fixing its base.

  • (DOC) Aggregate crushing value Test Lab Report | Adnan ...

    Name of the experiment: Aggregate Crushing value test. Objective: 1. Determine the aggregate crushing value of coarse aggregate. 2. Assess suitability of coarse aggregates for use in different types of road. Theory: The “aggregate crushing value” give a relative measure of the resistance of an aggregate to crushing under gradually applied ...

  • IMPACT VALUE OF AGGREGATE - iricen.gov

    2019-3-11 · fresh test made. Two tests shall be made. 5.Calculation 1.The ratio of the weight of fines formed to the total sample weight in each test shall he expressed as a percentage, the result being recorded to the first decimal place: Aggregate Impact Value = (B/A) X 100 where A = weight in g of saturated surface - dry sample,

  • Aggregate Impact Value Test | Construction Aggregate ...

    2017-10-4 · The test sample consist of aggregates passing 12.5 has been standardized by the So they must be tested for their mm sieve and retained on 10 mm sieve and dried in an Weight of aggregate(M1), g 313.4 315.4 329.1 British Standard The aggregate impact toughness before they are used in the oven for four hours at a temperature 100C to 110C and value ...

  • Impact Test on Aggregates - GharPedia

    2022-1-12 · The value of aggregate impact test should not be more than 45% by weight of aggregates, used for concrete other than wearing surface. An impact value 35% is permissible for the bituminous macadam. Maximum permissible impact value for the water bound macadam is 40%. The price of aggregate impact testing machine is approximately Rs 4000 to 6000 ...

  • AGGREGATE CRUSHING VALUE - iricen.gov

    2019-3-11 · 1.The ratio of the weight of fines formed to the total sample weight in each test shall be expressed as a percentage, the result being recorded to the first decimal place: Aggregate Crushing Value = (B/A) X 100 where A = weight of oven-dried sample B = weight in 'g' of fraction passing through 2.36 mm IS sieve. 6.Video Aggregate Crushing Value Test

  • Methods for determination of aggregate impact value

    2019-10-18 · Aggregate Impact Value (AIV) = 𝑾 𝑾 × Calculate the mean of the two results to the nearest whole number. Report the mean as the aggregate impact value, unless the individual results differ by more than 0.15 times the mean value. In

  • AGGREGATE IMPACT TEST by Nurul Afiqah - Prezi

    2014-3-26 · design by Dóri Sirály for Prezi AGGREGATE IMPACT TEST In conclusion,the percentage of aggregate’s wear depends on the quality of aggregate. In this test, we can conclude that: The loss of aggregate = 1663 g

  • AGGREGATE IMPACT VALUE (IS:2386-Part IV

    2013-5-7 · Objective For determination of the aggregate impact value of coarse aggregate, which passes 12.5 mm. IS sieve and retained on 10 mm. IS sieve. Reference Standards IS: 2386(Part IV)-1963 Methods of test for aggregate for

  • Los Angeles abrasion test- Step by Step

    The maximum value for the road pavement should be 60%. Precaution of test. The machine should be revolved at uniform speed. The sample of aggregate should be carefully chosen according to the IS code. The aggregates should

  • SPECIFICATIONS FOR TRACK BALLAST - 122.252.243.98

    2006-10-11 · Aggregate Impact Value = B/A X 100. 4 3 Two such tests shall be carried out and the mean of the results shall be reported to the nearest whole number as the Aggregate Impact Value of the tested material. Annexure-3. Water Absorption (Based on IS:2386 part HI - 1963) 1. Apparatus. The apparatus shall consist of the following:

  • Aggregate Impact Value - Civil Engineering

    2008-9-14 · AGGREGATE IMPACT VALUE This test is done to determine the aggregate impact value of coarse aggregates as per IS: 2386 (Part IV) – 1963. The apparatus used for determining aggregate impact value of coarse